Pressure Washing

How to Winterise a Pressure Washer

Protecting pumps, hoses and fittings from frost damage before the cold sets in.

A pressure washer left with water sitting inside it over a cold night is one of the most preventable ways to lose a machine for the season. Water expands by around 9% as it freezes, and inside a sealed pump chamber or hose fitting that expansion has nowhere to go — so something cracks instead. For UK contractors who rely on a washer through autumn and into spring, a few minutes of winterising now is far cheaper than a replacement pump in January.

Why Frozen Water Damages a Pressure Washer

The risk isn’t limited to the obvious parts. Water can sit in the pump head, the internal valves, the hose, the trigger gun and the lance — anywhere water passes through and isn’t fully drained. Once it freezes and expands, the most common failure is a cracked pump casting, but hose fittings, O-rings and seals can also split or perish, leading to leaks that only show up once the machine is back in use.

This kind of damage is rarely covered under warranty, because it’s considered preventable rather than a manufacturing fault. That makes winterising a cheap insurance policy rather than an optional extra, especially for a machine that’s central to daily contract work.

When UK Weather Starts to Bite

First frosts typically arrive across the UK from November into December, though timing varies a lot by region. Northern areas and anywhere at higher altitude tend to see frost earlier and more often, while milder coastal and southern areas usually see it later in the year. Local microclimates matter too — a yard or storage area that sits in a dip or gets no sun can frost well before the wider forecast suggests.

The practical takeaway is not to wait for a cold snap to catch you out. Early autumn, before the first proper frost warning, is the right time to get equipment protected, particularly if a machine won’t be used daily through the winter months.

Winterising a Pressure Washer: Step by Step

  1. Release the pressure and disconnect the water supply. Run the trigger gun briefly to relieve any pressure left in the system before disconnecting hoses.
  2. Run a pump protector through the inlet. A proper pump saver or pump antifreeze, drawn through the inlet until it appears at the outlet, displaces the water inside the pump and coats the internal seals. This is the most reliable single step and only takes a few minutes.
  3. Drain the hose, lance and gun separately. Water can sit in low points of the hose even after the main unit is drained, so uncoil it fully and let it run out, or use compressed air to purge the line if one is available.
  4. Deal with the engine, if petrol or diesel. Either run the fuel tank dry or add a fuel stabiliser, and change the engine oil before long-term storage so the machine isn’t sitting with old, contaminated oil over winter.
  5. Store the machine somewhere that won’t drop below freezing. This is the step most often got wrong — see below.

If you only do one thing: get pump antifreeze through the system. Draining alone is better than nothing, but it rarely removes every trace of water from a pump’s internal passages, and it’s the water you can’t see that does the damage.

Don’t Forget Hoses, Reels and Water-Fed Pole Kit

Pressure washers aren’t the only equipment at risk. Any hose reel, delivery hose or fitting left full of water can split in exactly the same way, and the same goes for water-fed pole systems, gutter vacuum hoses and their pumps. Uncouple and drain hose reels fully rather than leaving them coiled and full, and if a water-fed pole van system sits unused for stretches over winter, draining the hose lines and protecting any external pump reduces the same freeze risk.

Resin vessels and filters on a water-fed pole system have their own maintenance needs separate from frost protection — that’s covered in more detail in our guide to DI resin exhaustion — but if a vehicle or unit is going to sit idle in cold weather, draining standing water out of the housing is a sensible extra step.

Where (and Where Not) to Store Equipment Over Winter

  • A domestic garage or outbuilding that stays a few degrees above freezing is usually adequate for short cold spells
  • An unheated van is often not good enough — metal bodywork loses heat quickly overnight and can sit colder than the air outside
  • If equipment has to stay in a van between jobs, treating it as if it will freeze (pump antifreeze, drained hoses) is the safer assumption
  • Avoid sealed plastic covers that trap condensation; a breathable cover or simply keeping the unit dry and off a cold concrete floor is better for long-term storage

If It Does Freeze Anyway

If a machine has been left out and you suspect it’s frozen, the safest approach is to bring it into a warmer space and let it thaw slowly and naturally. Don’t apply direct heat such as a heat gun or hot water to the pump, and don’t attempt to start the engine or motor until you’re confident it has fully thawed — trying to force a pump that still has ice inside it is how a borderline crack becomes a full failure.

Frequently Asked Questions

Can I just leave my pressure washer in the van over winter?

It’s risky. Unheated vans can get colder overnight than you’d expect, so if a machine has to live in a van, treat it as if it will freeze and winterise it properly rather than relying on the van to keep it warm.

Is draining the pump enough, or do I need antifreeze too?

Draining helps, but it’s very difficult to remove every trace of water from a pump’s internal passages by draining alone. Running a proper pump antifreeze or pump saver through the system gives much more reliable protection.

Does this apply to electric pressure washers as well as petrol ones?

Yes — the frost risk to the pump and hoses is the same regardless of power source. Petrol and diesel machines have the extra step of dealing with fuel and engine oil before storage.

When should I winterise my equipment?

Before the first hard frost of the season, which in the UK typically arrives from November onwards, earlier in northern and higher-altitude areas. It’s better to do it too early than to be caught out by an early cold snap.

Get Set Up Before the Cold Hits

Browse pump savers, hose reels and pressure washers in our range, or get in touch if you need a replacement machine or hire cover while yours is out of action.

Shop Pressure Washers
Talk to Us